Wfly ET Series Instruction Manual Download | Manualshive

Page: 74 / 131

background image

Swash mixing

Swash mixing

Mixing

AIL to ELE

ELE to AIL

PIT to AIL

PIT to ELE

Rate2

Rate1

+0%

+0%

+0%

+0%

+0%

+0%

+0%

+0%

2/2

Interface path: WFLY → [Model Menu] → [Swash Mixing]

The swash mixing is used to correct the swash movement in the aileron (rolling) direction and the

elevator (helicopter head pitch) according to the speciﬁc operation under each ﬂight condition.

Flight condition: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching is

performed by switches, and function settings are made separately.

This feature allows individual adjustments to the rate of each set of ailerons, elevators and pitches.

Applications

● Example: Use the swash mixes function to correct the unintended movement trend of the roll direction.
● Use "Aileron to Elevator" mixing. Set this function "Enable" to adjust with the ratio. When the helicopter

is raised to the right roll head, the value should be adjusted at "Rate 2", the right aileron moves, and the
elevator deﬂects downward. Rolling to the left should adjust the value at "Rate 1"

Swash mixing

Mixing

Status

AIL to ELE

ELE to AIL

PIT to AIL

PIT to ELE

INH

INH

INH

INH

Trim

Switch

- -

- -

- -

- -

- -

- -

1/2

When the mixing control switch is set to [--], the swash
mixing only works under the selected ﬂight conditions.

Can be set to knob switch, etc., default [--]

Mixing on and oﬀ options

The left mixing, default 0%, range -100%~+100%

The right mixing, default 0%, range -100%~+100%

074

Model Menu\Helicopter

«
...
72
73
74
75
76
...
»

Summary of Contents for ET Series




































































































































Reviews:

No comments

Related manuals for ET Series

Brand: YASKAWA Pages: 256

Brand: CALEFFI Pages: 12

QuickSetter+ 132 Series

Brand: CALEFFI Pages: 5

ESD-5550 Series

Brand: GAC Pages: 12

Brand: Hach Pages: 2

Brand: Hach Pages: 12

Brand: Hach Pages: 472

Brand: Hach Pages: 64

Brand: V2 ELETTRONICA Pages: 6

Brand: Hach Pages: 210

Brand: Hanna Instruments Pages: 88

Brand: Quectel Pages: 90

Brand: tau Pages: 9

Brand: tau Pages: 8

Brand: Vaillant Pages: 11

IntelliZone2 MasterStat

Brand: Water Furnace Pages: 44

Brand: Saluki Pages: 13

XP-9 88-IoT Series

Brand: ICP DAS USA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands