Wfly ET Series Instruction Manual Download Page 95

Page: 95 / 131

Status

Switch

Camber ﬂap to ELE

INH

- -

ELE

+0%

Rate1

Rate2

Camber Flap to Elevator

Function status switch (INH, ON, default [INH])

Control switch assignment, default [--]

Diﬀerent aircraft types will have diﬀerent wings

Adjust in positive and negative directions, range ±120%, default 0%

Interface path: WFLY → [Model Menu] → [Camber ﬂap to ELE]

When using ﬂaps, the pitch angle of the model has a tendency to change. This mixing compensates for

the attitude change of the model by combining the inputs of the elevator.

The ratio of the upper and lower directions of the elevator can be adjusted. If the mixing direction is

reversed due to a connection problem, you can also make adjustments by changing the polarity of the ratio.

In ﬂight, this function can be switched on or oﬀ with the switch (set to [ - ] if it is always on, or [ - ], and the

position is "on" to achieve the function normally on.)

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition] to switch

through the switches and perform function settings separately.

Diﬀerent types of interface on the wing type

ELE

ELE2

(Aileron to Elevator)

Flaps

Flaps2

V-tail

095

Model Menu\Airplane

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Brands by name

Popular brands