Wfly ET Series Instruction Manual Download Page 114

Page: 114 / 131

Elevator to Camber

Elevator to camber

Status

INH

Switch

- -

AIL

+100%

AIL2

+100%

Rate1

Rate2

Interface path: WFLY → [Model Menu] → [Elevator to Camber]

Use this functon when you need to mix ﬂap operation and elevator operation. When the mixing control is

turned on, the elevator will be raised while the ﬂap is lowered, which can increase the lift.

Function status switch (INH, ON, default [INH])

Control switch assignment, default [--]

Diﬀerent aircraft types are with diﬀerent wings

Adjust in the positive and negative directions, range
±100%, default 0%

This function can be switched "on" or "oﬀ" with the switch during ﬂight. (If you want to keep it on, set it to

[--], you can also set it to [--], and the position is "On" to achieve the function normally open.)

When the mixing is activated, the elevator on the tailless wing is also aﬀected.

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching is

performed by switches, and function settings are made separately. * The interface is diﬀerent from the
wings.

114

Model Menu\Glider

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Brands by name

Popular brands