Wfly ET Series Instruction Manual Download | Manualshive

Page: 27 / 131

background image

Display

10

Backlight max

Backlight min

Time

Auto oﬀ time

Auto lock

10

30Sec

Never

Never

System Setting

Display

Interface Path: WFLY → [System Setting] → [Display]

Adjust the brightness of the display backlight, the shutdown time, and the lock screen time to

adapt to different environments and energy saving.

The backlight switches to the "Backlight max" value!

Lock screen after when the touch screen has no operation.

The transmitter is turned oﬀ after no operation.

It means that no button and touch screen operation time is
detected after setting value.

The darkest brightness value of normal standby.

Parameter Value Setting(taking the maximum backlight as an example):

Click the “Backlight max” value box and click the parameter adjustment buttons [▼], [▲] according to the

visual eﬀect.

The maximum backlight, the default is 10, the range: 1~20, the setting value can't be lower than the

minimum backlight setting value.

The minimum backlight, the default is 10, the range: 1~20, the setting value can't be higher than the

maximum backlight setting value.

Backlight time, default 30 seconds, 15 seconds, 30 seconds, 1 minute, 2 minutes, 5 minutes, 10 minutes,

always bright.

Auto power oﬀ time, default oﬀ, 30 minutes, 40, 50, 60 minutes, oﬀ.
Automatic lock screen time, default oﬀ, 15 seconds, 30 seconds, 1 minute, 2 minutes, 5 minutes, 10

minutes, oﬀ.

027

High brightness display will increase
the energy consumption of the
transmitter, which will aﬀect the
working time of the transmitter. Please
pay attention to setting the transmitter
voltage alarm. Pay attention to the
battery level and avoid low battry
operation of the transmitter.

WARNING

«
...
25
26
27
28
29
...
»

Summary of Contents for ET Series




































































































































Reviews:

No comments

Related manuals for ET Series

Brand: Farris Engineering Pages: 12

Brand: Eastern Times Technology Pages: 4

Brand: Vacon Pages: 18

Brand: Watts Pages: 2

Brand: Ultra Start Pages: 8

Brand: FAAC Pages: 12

Brand: FAAC Pages: 60

Brand: FAAC Pages: 12

Brand: FAAC Pages: 44

Brand: FAAC Pages: 44

Brand: FAAC Pages: 8

Brand: FAAC Pages: 60

Brand: FAAC Pages: 14

Brand: FAAC Pages: 68

Brand: FAAC Pages: 16

Brand: FATEK Pages: 10

Brand: Garmin Pages: 4

Brand: Rain Bird Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands