Wfly ET Series Instruction Manual Download

Page: 113 / 131

Camber Mix

Camber mix

Status

INH

Switch

AIL

+0%

AIL2

+0%

ELE

+0%

ELE2

+0%

Rate1

Rate2

- -

Interface path: WFLY → [Model Menu] → [

]

Camber Mix

This function is used to adjust the operating ratio on the positive and negative directions (ailerons, ﬂaps)

of the airfoil ﬂaps. The ratio of the ailerons, ﬂaps, and elevators can be individually adjusted to correct for
changes in attitude caused by airfoil operations. The interface of diﬀerent wing types will also be the same.

Function status switch (INH, ON, default [INH])

Control switch assignment, default [--]

Diﬀerent aircraft types will have diﬀerent wings

Adjust in the positive and negative directions,
range ±100%, default 0%

The up/down ratio of the ailerons, ﬂaps, and elevators can be adjusted separately using curves. When

the mechanical connection action of the fuselage is opposite to the mixing direction, the mixing polarity can
be changed to adjust (+ or -).

This function can be switched "on" or "oﬀ" with the switch during ﬂight. (If you want to keep it on, set it to

[--], you can also set it to [--], and the position is "On" to achieve the function normally open.)

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching is

performed by switches, and function settings are made separately.

Elevator

Elevator2(Aileron Elevator)

Ailero

Ailero2

V-tail

Flap

Flap2

113

Model Menu\Glider

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands