background image

Troubleshooting

211

Troubleshooting

Troubleshooting 

table

Problem

Possible cause

Solution

Pag.

Incorrect 
application 
rates (kg per 
hectare)

Dosing setting incorrectly set

Check the dosing setting

133

Incorrect setting for fine application

Set the dosing setting for fine application 
as per the instructions

115

Driving speed signal not correctly set

Set the correct source of the driving speed 
signal in the control system, as well as the 
control box

77

Incorrect driving speed signal

Calibrate the driving speed

Incorrect distance between the driving 
tracks

Always set out the driving tracks before 
spreading

156

New type of fertiliser spread with the 
same settings as the previous type. 
Quality varies greatly between types

Determine the characteristics of the 
fertiliser, look for the relevant spreading 
chart and set the spreader again

100

105

The flow of the fertiliser is blocked

Clean the machine thoroughly after each 
use. Replace the agitator if it is worn out

177

Dosing setting and flow rate not entered 
on the ‘Curve Calibration’ screen before 
starting work activities

Find the correct values in the spreading 
chart and enter them

112

Incorrect application rate and/or working 
width entered

Enter the correct application rate and 
working width in the control system.

105

The control system is being operated 
manually, so it does not perform 
automatic calibration

Switch to automatic operation

Incorrect values entered after a manual 
calibration test at a manually entered 
application rate

Perform the calibration test in the correct 
manner and enter the result obtained

123, 
119

The speedometer is incorrect or not 
measuring.

Check the sensors and cables and 
calibrate the wheel sensor or radar

51

For a tractor without driving speed 
measurement: the simulated and real 
driving speeds do not correspond

Adjust the simulated driving speed on the 
main screen or the real driving speed

51

Difference 
between the 
flowrate on the 
left and the 
right spreading 
discs

Dosing setting or discharge points are not 
set the same

Check the settings

105

The stop of one or both of the actuators 
have been moved

Check the position of the connecting 
points and readjust them

191

Discharge on one side is blocked

Clean the machine thoroughly after each 
use. Replace the agitator if it is worn out

177

Summary of Contents for RO-M EW


































































































































































































































Reviews: