manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 97 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 97

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

9210

Unsigned / 2

Flow direction 

Flow direction filter ap‐

plicable for Process val‐

ues (9204) = 0, 1, 19 

and 27.

0

● 0: Positive direction
● 1: Negative direction
● 2: Positive and 

negativedirections

● 3: Positive and 

negative directions 
(symmetric mode)

Read / 

write

9235

Float / 4

Frequency val‐

ue high

Upper frequency value.

Upper nominal output 

range boundary.

10000.0

[Hz]

0.0 - 12500.0

Read / 

write

9237

Float / 4

Frequency val‐

ue low

Lower frequency value.

Lower nominal output 

range boundary.

0.0 Hz

0.0 - 12500.0

Read / 

write

9215

Float / 4

Upper range 

value volume 

flow

Upper volume flow val‐

ue that is mapped to 

the upper nominal 

range boundary selec‐

ted by Frequency value 

high (9235). Applicable 

if Process value (9204) 

= 1.

0.4 % • max. 

volume flow

[m

3

/s]

(7500)

-

Read / 

write

9217

Float / 4

Lower range 

value volume 

flow

Lower volume flow val‐

ue that is mapped to 

the lower nominal 

range boundary selec‐

ted by Frequency value 

low (9237). Applicable 

if Process value (9204) 

= 1.

0.0

[m

3

/s]

(7500)

-

Read / 

write

9211

Float / 4

Upper range 

value mass flow

Upper mass flow value 

that is mapped to the 

upper nominal range 

boundary selected by 

Frequency value high 

(9235). Applicable if 

Process value (9204) = 

0.

0.2 • max. 

mass flow

[kg/s]

(7400)

-

Read / 

write

9213

Float / 4

Lower range 

value mass flow

Lower mass flow value 

that is mapped to the 

lower nominal range 

boundary selected by 

Frequency value low 

(9237). Applicable if 

Process value (9204) = 

0.

0.0

[kg/s]

(7400)

-

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

97

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments