Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 189

Page: 189 / 198

4.10.13

Communication

4.10.13.1

Service channel

Table 4-116 Service channel

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

9594

Unsigned / 2

USB mode

Returns the USB mode. -

● 0: USB

communication

● 1: Mass storage

device (MSD)

Read

only

9595

Unsigned / 2

Auto mode

Automatically connec‐

ted as MSD when USB

cable is plugged.

● 0: Disabled
● 1: Enabled

Read /

write

9596

Unsigned / 2

MSD connect

Command to connect /

disconnect to PC.

● 0: Cancel
● 1: Connect
● 2: Disconnect

Write on‐

4.10.14

Security

4.10.14.1

Access management

Table 4-117 Access management

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

8292

Unsigned / 2

User PIN

Input of user PIN.

Write on‐

8293

Unsigned / 2

Expert PIN

Input of expert PIN.

Write on‐

8294

Unsigned / 2

Access level

Granted access level.

● 16: Read only
● 32: User privilege
● 64: Expert privilege

Read

only

6169

Unsigned / 2

New user PIN

Input to change user

PIN.

Write on‐

6170

Unsigned / 2

New expert PIN Input to change expert

PIN.

Write on‐

ly (Ex‐

pert)

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

189

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 189 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: