Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 125

Page: 125 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

9076

Unsigned / 2

value

Selection of the fifth val‐

ue. Depending on the

number of values.

See Selectable values

dependent on the view

type (Page 133).

Read /

write

9077

Unsigned / 2

value

Selection of the sixth

value. Depending on

the number of values.

See Selectable values

dependent on the view

type (Page 133).

Read /

write

8050

Unsigned / 2

Trend scale

mode

Scaling mode for the

graph and totalizer

view.

● 0: Automatic scaling.
● 1: Fixed scaling

defined by Trend
scale lower limit
(8052) and Trend
scale upper limit
(8054).

Read /

write

8051

Unsigned / 2

Trend log time

window

Scaling of the time axis.

Effective when Trend

scale mode (8050) is

set to 1.

● 0: 1 min
● 1: 5 min
● 2: 15 min
● 3: 30 min
● 4: 1 h
● 5: 2 h
● 6: 3 h

Read /

write

8052

Float / 4

Trend scale low‐

er limit

Scaling of the y-axis.

Lower limit. Effective

when Trend scale

mode (8050) is set to 1.

0.0

Read /

write

8054

Float / 4

Trend scale up‐

per limit

Scaling of the y-axis.

Upper limit. Effective

when Trend scale

mode (8050) is set to 1.

0.0

Read /

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

125

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 125 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: