manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 76 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 76

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8339

Float / 4

Standard vol‐

ume lower 

alarm limit

Falling below this limit 

causes an alarm when 

volume flow is selected 

as input.

Min. floating 

point value

[Sl]

(8322)

 

Read / 

write

8341

Float / 4

Standard vol‐

ume alarm hys‐

teresis

Hysteresis that affects 

the alarm and warning 

limits when volume 

flow is selected as in‐

put.

0.0

[Sl]

(8322)

-

Read / 

write

Totalizer 2 settings

Table 4-28

Totalizer 2 settings   

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8405

Unsigned / 2

Process value

Select process value 

for totalization.

0

● 0: Cut-off filtered 

mass flow

● 1: Cut-off filtered 

volume flow

● 4: Corrected volume 

flow

● 5: Fractional flow 

medium A

● 5: Fractional flow 

medium B

Read / 

write

8402

Unsigned / 2

Fail-safe behav‐

ior

Behavior of the totaliz‐

er during the occur‐

ence of bad input value.

0

● 0: RUN; totalization is 

continued using the 
bad input value.

● 1: HOLD; totalization 

is stopped.

● 2: MEMORY; 

totalization is 
continued based on 
the last incoming 
good value.

Read / 

write

8423

Float / 4

Volume upper 

alarm limit

Exceeding this limit 

causes an alarm when 

volume flow is selected 

as input.

Max. floating 

point value

[m

3

]

(8421)

 

Read / 

write

8425

Float / 4

Volume upper 

warning limit

Exceeding this limit 

causes a warning when 

volume flow is selected 

as input.

Max. floating 

point value

[m

3

]

(8421)

 

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

76

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments