Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 38

Page: 38 / 198

4.5

Integer byte order

The device is able to adjust the byte order of integer values.

Table 4-4

Integer byte order

Modbus

Data type /

Size in

bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting op‐

tions

Access

level

8295

Unsigned /

Integer order byte

The integer byte order used

in Modbus messages.
0: MSB - LSB (big endian)
1: LSB - MSB (little endian)
MSB = most significant byte /

high byte
LSB = least significant byte /

low byte

MSB - LSB

(big endian)

0 - 1

Read /

write

4.6

Float transmission

The Float Byte Order function ensures that the master and slave use the same sequence of

the bytes when transmitting float values. This enables the user to configure the FCT030 and

operate the device with all types of PLCs without reprogramming the PLC. The transmission

order is configured by setting the parameter Byte Order in the submenu Device →

Communication.

Note
The command Restart Communication must be executed to activate the new byte order setting.

The table in chapter Float byte order (Page 39) shows the different options for setting the

transmission method.

MODBUS commands
4.6 Float transmission

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 38 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: