manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 47 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 47

Modbus 

register

Data type / 

Size in bytes

Parameter

Description Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

● 171: BBL31/min (1 barrel = 31 US 

gallons)

● 172: BBL31/h (1 barrel = 31 US 

gallons

7400

Unsigned / 2

Mass flow units Units for 

mass flow 

values.

75

● 70: g/s (grams per second)
● 71: g/min (grams per min)
● 72: g/h (grams per hour)
● 73: kg/s (kilograms per second)
● 74: kg/min (kilograms per minute)
● 75: kg/h (kilograms per hour)
● 76: kg/d (kilograms per day)
● 77: t/min (1 t = 1000 kg)
● 78: t/h (1 t = 1000 kg)
● 79: t/d (1 t = 1000 kg)
● 80: lb/s (pounds per second)
● 81: lb/min (pounds per minute)
● 82: lb/h (pounds per hour)
● 83: lb/d (pounds per day)
● 84: STon/min (1 STon = 2000 lb)
● 85: STon/h (1 STon = 2000 lb)
● 86: STon/d (1 STon = 2000 lb)
● 87: T/h (1 T = 2240 lb)
● 88: T/d (1 T = 2240 lb)
● 253: custom units (see Custom 

mass flow units string (8458) / 
factor (8456))

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

47

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments