manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 19 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 19

Updating the Electronic Device Description (EDD) 
You can locate the EDD in the SIMATIC PDM Device Library under Devices → Modbus → 

Sensors → Flow → Coriolis → Siemens AG → SITRANS FC430 and FC330. Check the product 

page of our website (

www.siemens.com/FC430

) under Support > Software downloads, to 

make sure you have the latest version of SIMATIC PDM, the most recent Service Pack (SP) 

and the most recent hot fix (HF). 
Installing a new EDD: 
1. Download the EDD from the product page of our website (

www.siemens.com/FC430

) and 

save the files to your computer. 
2. Extract the zipped file to an easily accessed location. 
3. Launch the SIMATIC PDM Device Integration Manager, browse to the unzipped EDD file 

and select it. 

See also

Commissioning steps (Page 17)
Wizard - Quick Start via PDM (Page 22)

Commissioning

3.5 Initial Setup

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

19

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments