manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 87 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 87

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8913

Float / 4

Lower range 

value mass flow

Lower mass flow value 

that is mapped to the 

lower nominal range 

boundary selected by 

Frequency value low 

(8937). Applicable if 

Process value (8904) = 

0.

0.0

[kg/s]

(7400)

-

Read / 

write

8919

Float / 4

Upper range 

value density

Upper process density 

value that is mapped to 

the upper nominal 

range boundary selec‐

ted by Frequency value 

high (8935). Applicable 

if Process value (8904) 

= 2.

1600

[kg/m

3

]

(7600)

-

Read / 

write

8921

Float / 4

Lower range 

value density

Lower process density 

value that is mapped to 

the lower nominal 

range boundary selec‐

ted by Frequency value 

low (8937). Applicable 

if Process value (8904) 

= 2.

600

[kg/m

3

]

(7600)

-

Read / 

write

8923

Float / 4

Upper range 

value tempera‐

ture

Upper medium temper‐

ature value that is map‐

ped to the upper nomi‐

nal range boundary se‐

lected by Frequency 

value high (8935). Ap‐

plicable if Process val‐

ue (8904) = 3.

Max. medium 

temperature

[°C]

(7700)

-

Read / 

write

8925

Float / 4

Lower range 

value tempera‐

ture

Lower medium temper‐

ature value that is map‐

ped to the lower nomi‐

nal range boundary se‐

lected by Frequency 

value low (8937). Appli‐

cable if Process value 

(8904) = 3.

Min. medium 

temperature

[°C]

(7700)

-

Read / 

write

8927

Float / 4

Upper range 

value standard 

volume flow

Upper standard volume 

flow value that is map‐

ped to the upper nomi‐

nal range boundary se‐

lected by Frequency 

value high (8935). Ap‐

plicable if Process val‐

ue (8904) = 27.

0.4 % • max. 

standard vol‐

ume flow

[Sm

3

/h]

(7964)

-

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

87

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments