manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 109 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 109

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

9306

Unsigned / 2

Current mode

Mode of current output. 0

● 0: 4-20 mA (3.5) 

3.8-20.5 (22.6) 
NAMUR

● 1: 4-20 mA (3.75) 

4.0-20.8 (22.6) US

● 2: 4-20 mA (2.0) 

4.0-20.5 (22.0)

● 3: 4-20 mA (2.0) 

4.0-24.0 (25.0)

● 4: 0-20 mA (0.0) 

0.0-20.5 (22.0)

● 5: 0-20 mA (0.0) 

0.0-24.0 (25.0)

Read / 

write

9366

Float / 4

Upper range 

value volume 

flow

Upper volume flow val‐

ue that is mapped to 

the upper nominal 

range boundary selec‐

ted by Current mode 

(9306). Aplicable if 

Process value (9302) = 

1.

0.4 % • max. 

volume flow

[m

3

/s]

(7500)

-

Read / 

write

9368

Float / 4

Lower range 

value volume 

flow

Lower volume flow val‐

ue that is mapped to 

the lower nominal 

range boundary selec‐

ted by Current mode 

(9306). Applicable if 

Process value (9302) = 

1.

0.0

[m

3

/s]

(7500)

-

Read / 

write

9310

Float / 4

Upper range 

value mass flow

Upper mass flow value 

that is mapped to the 

upper nominal range 

boundary selected by 

Current mode (9306). 

Applicable if Process 

value (9302) = 0.

0.2 • max. 

mass flow

[kg/s]

(7400)

-

Read / 

write

9312

Float / 4

Lower range 

value mass flow

Lower mass flow value 

that is mapped to the 

lower nominal range 

boundary selected by 

Current mode (9306). 

Applicable if Process 

value (9302) = 0.

0.0

[kg/s]

(7400)

-

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

109

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments