Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 60

Page: 60 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

2442

Float / 4

Density Correc‐

tion
Factor

Set density compensa‐

tion
value (gain) in order to

make
a density correction

(scale
factor).
To increase the dis‐

played
density value with +0.5

%,
set the density factor to
1.005.
The displayed density

value
will now be 0.5 % higher
than before

-1.999 to
+1.999

Read /

write

2444

Float / 4

Density Correc‐

tion
Offset

Set density compensa‐

tion
value (offset) in order to
make an offset on the

measured
density.
To make the flowmeter

show
+ 2 kg/m3, change the

density
offset to 2.000 kg/m3 in

the
'Sensor' menu

[kg/m

]

-1 400 to +1
400

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 60 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: