Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 155

Page: 155 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

8608

Float / 4

Recipe 1

amount mass

flow

Target amount for dos‐

ing mass flow

Read /

write

8610

Float / 4

Recipe 1

amount volume

flow

Target amount for dos‐

ing volume flow

Read /

write

8612

Float / 4

Recipe 1

amount correc‐

ted volume flow

Target amount for dos‐

ing corrected volume

flow

Read /

write

7583

Unsigned / 2

Recipe 1 Dec.

point mass flow

Specify the selected

number of decimals for

mass flow

Read /

write

7584

Unsigned / 2

Recipe 1 Dec.

point volume

flow

Specify the selected

number of decimals for

volume flow

Read /

write

7585

Unsigned / 2

Recipe 1 Dec.

point corrected

volume flow

Specify the selected

number of decimals for

corrected volume flow

Read /

write

8615

Float / 4

Recipe 1 fixed

compensation
Mass flow

Fixed compensation

mass flow value that is

used to close the

valve(s) before the

measured amount val‐

ue has reached the tar‐

get amount

Read /

write

8617

Float / 4

Recipe 1 fixed

compensation
Volume flow

Fixed compensation

volume flow value that

is used to close the

valve(s) before the

measured amount val‐

ue has reached the tar‐

get amount

Read /

write

8619

Float / 4

Recipe 1 fixed

compensation
Corrected vol‐

ume flow

Fixed compensation

corrected volume flow

value that is used to

close the valve(s) be‐

fore the measured

amount value has

reached the target

amount

Read /

write

8691

Unsigned / 2

Recipe 1 com‐

pensation mode

Compensation algo‐

rithm, fixed or adaptive

compensation

0: fixed compensation

value is taken
1: On Target
2: Target plus
3: Target minus

Read /

write

8625

Float / 4

Recipe 1 over‐

run mass flow

value

When the amount

mass flow has reached

this value a dosing

overrun fault is raised.

Read /

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

155

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 155 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: