manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 168 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 168

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

10558

Unsigned / 2

Error status

Error status if config‐

ured to current input.

-

● Bit 0: Overflow (> 25 

mA)

● Bit 1: Underflow (< 0 

mA)

● Bit 2: Measured 

current out of 
measuring range

Read 

only

9129

Unsigned / 2

Digital input val‐

ue

Input value if config‐

ured to digital input.

-

-

Read 

only

Channel 4

Table 4-85

Channel 4   

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

9303

Float / 4

Current output 

value

Output current value if 

configured to current 

output.

-

-

Read 

only

9328

Unsigned / 2

Error status

Error status if config‐

ured to current output.

-

● Bit 0: Overflow
● Bit 1: Underflow
● Bit 2: Fail mode 

activated

● Bit 3: Cable break
● Bit 4: Output current 

cannot be 
established (read 
back deviation > 0.1 
mA)

Read 

only

9340

Unsigned / 2

Status output

Status value if config‐

ured to status output.

-

-

Read 

only

9469

Float / 4

Pulse status 

output

Amount done if config‐

ured to pulse output.

-

-

Read 

only

9472

Unsigned / 2

Error status

Error status if config‐

ured to pulse output.

-

● Bit 0: The pulse 

output has reached 
the maximum pulse 
output frequency

● Bit 1: Fail mode is 

activated

Read 

only

9487

Unsigned / 4

Pulse counter

Pulse output since 

startup.

-

-

Read 

only

9400

Float / 4

Frequency out‐

put value

Frequency value if con‐

figured to frequency 

output.

-

-

Read 

only

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

168

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments