manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 154 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 154

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

8599

Unsigned / 2

Dosing cycle 

counter reset

Command to reset the 

dosing cycle counter

-

0: do nothing
1: reset cycle counter

Read / 

write

8595

Unsigned / 2

Dosing active 

recipe

Activate recipe (1 to 5) 

parameter set. Every 

recipe consists of an 

own set of parameters

1

1 : Recipe 1 active
2 : Recipe 2 active
3 : Recipe 3 active
4 : Recipe 4 active
5 : Recipe 5 active

Read / 

write

Dosing - recipe 1

Table 4-77

Dosing – recipe 1

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

8600

String / 16

Recipe 1 name Name of recipe param‐

eter set

-

 

Read / 

write

8678

Unsigned / 2

Recipe 1 unit 

mass flow

Mass flow unit for dos‐

ing parameters 
 

61

60: grams
61: kilograms
62: metric tons
63: pounds
64: short tons
65: long tons
125: ounces
 

Read / 

write

8679

Unsigned / 2

Recipe 1 unit 

volume flow

Volume flow unit for 

dosing parameters 
 

41

40: US gallons
41: liters
42: imperial gallons
43: cubic meters
46: oil barrels
110: bushels
111: cubic yards
112: cubic feet
113: cubic inches
124: liquid barrels
170: beer barrels
236: hectoliters

Read / 

write

8680

Unsigned / 2

Recipe 1 unit 

corrected vol‐

ume flow

Corrected volume flow 

unit for dosing parame‐

ters 
 

166

166: normal cubic meters
167: normal liters
168: standard cubic feet
171: standard liters
172: standard cubic me‐

ters

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

154

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments