manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 49 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 49

Modbus 

register

Data type / 

Size in bytes

Parameter

Description Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

7600

Unsigned / 2

Density units

Units for 

density val‐

ues.

92

● 91: g/cm³ (grams per cubic) 

centimeters

● 92: kg/m³ (kilograms per cubic 

meter)

● 93: lb/gal (pounds per US gallon)
● 94: lb/ft³ (pounds per cubic foot)
● 95: g/ml (grams per mililiter)
● 96: kg/l (kilograms per liter)
● 97: g/l (grams per liter)
● 98: lb/in³ (pounds per cubic inch)
● 99: STon/yd³ (1 STon = 2000 lb)
● 146: μg/l (micrograms per liter)
● 147: μg/m³ (micrograms per cubic 

meter)

● 170: mg/l (milligrams per liter)
● 253: custom units (see Custom 

density units string (8464) / factor 
(8462))

Read / 

write

7700

Unsigned / 2

Temperature 

units

Units for 

tempera‐

ture values.

32

● 32: °C (degrees Celsius)
● 33: °F (degrees Fahrenheit)
● 34: °R (degrees Rankine)
● 35: K (kelvins)

Read / 

write

8321

Unsigned / 2

Totalizer 1 units Units for 

volume 

quantities 

of totalizer 

1 (totalizer 

1 is config‐

ured to vol‐

ume flow).

41

● 40: US gallons
● 41: l (liters)
● 42: i.gal (Imperial gallons)
● 43: m³ (cubic meters)
● 46: BBL42 (1 barrel = 42 US 

gallons)

● 110: bush (bushels)
● 111: yd³ (cubic yards)
● 112: ft³ (cubic feet)
● 113: in³ (cubic inches)
● 124: BBL31.5 (1 barrel = 31.5 US 

gallons)

● 170: BBL31 (1 barrel = 31 US 

gallons)

● 236: hl (hectoliters)
● 253: custom units (see Custom 

volume units string (8452) / factor 
(8450))

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

49

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments