manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 128 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 128

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

9026

Unsigned / 2

3

rd

 value

Selection of the third 

value. Depending on 

the number of values.

0

See Selectable values 

dependent on the view 

type (Page 133).

Read / 

write

9081

Unsigned / 2

4

th

 value

Selection of the fourth 

value. Depending on 

the number of values.

1

See Selectable values 

dependent on the view 

type (Page 133).

Read / 

write

9082

Unsigned / 2

5

th

 value

Selection of the fifth val‐

ue. Depending on the 

number of values.

11

See Selectable values 

dependent on the view 

type (Page 133).

Read / 

write

9083

Unsigned / 2

6

th

 value

Selection of the sixth 

value. Depending on 

the number of values.

12

See Selectable values 

dependent on the view 

type (Page 133).

Read / 

write

8062

Unsigned / 2

Trend scale 

mode

Scaling mode for the 

graph and totalizer 

view.

0

● 0: Automatic scaling.
● 1: Fixed scaling 

defined by Trend 
scale lower limit 
(8064) and Trend 
scale upper limit 
(8066).

Read / 

write

8063

Unsigned / 2

Trend log time 

window

Scaling of the time axis. 

Effective when Trend 

scale mode (8062) is 

set to 1.

1

● 0: 1 min
● 1: 5 min
● 2: 15 min
● 3: 30 min
● 4: 1 h
● 5: 2 h
● 6: 3 h

Read / 

write

8064

Float / 4

Trend scale low‐

er limit

Scaling of the y-axis. 

Lower limit. Effective 

when Trend scale 

mode (8062) is set to 1.

0.0

-

Read / 

write

8066

Float / 4

Trend scale up‐

per limit

Scaling of the y-axis. 

Upper limit. Effective 

when Trend scale 

mode (8062) is set to 1.

0.0

-

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

128

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments