Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 32

Page: 32 / 198

Drop-down menus

Table 3-1

Device menus

Description

Download to Device

Downloads all writable parameters to the device

Upload to PC/PG

Uploads all parameters from the device to the parameter
table

Assign address and TAG

Assign communication address and TAG name

Value comparison

Compare values between device / project

Object properties

Properties for device and project

Calibration log

Create calibration logs for field devices.

Change log

The change log records which actions have been per‐

formed with SIMATIC PDM on devices

Set the device checked

The device can be set to checked / or unchecked

Check configuration

Check configuration if it contains errors

Wizard - Quick Start

Guide for a quick commissioning

Wizard - Zero Point Adjustment

Guide for zero point adjustment (automatic and manual)

Table 3-2

View menus

Description

Process Variables (online dialog)

Shows all process values

Device Diagnostic (online dialog)

Shows all diagnostics information (alarms and diagnostics

parameters)

Toolbar (online dialog)

Shows/hides the toolbar

Status Bar

Shows/hides the status bar

Update

Updates the content of the active window

Commissioning
3.11 Parameters accessed via drop-down menus

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 32 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: