manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 110 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 110

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

9370

Float / 4

Upper range 

value density

Upper process density 

value that is mapped to 

the upper nominal 

range boundary selec‐

ted by Current mode 

(9306). Applicable if 

Process value (9302) = 

2.

Max. denisty

[kg/m

3

]

(7600)

-

Read / 

write

9372

Float / 4

Lower range 

value density

Lower process density 

value that is mapped to 

the lower nominal 

range boundary selec‐

ted by Current mode 

(9306). Applicable if 

Process value (9302) = 

2.

0.08

[kg/m

3

]

(7600)

-

Read / 

write

9374

Float / 4

Upper range 

value tempera‐

ture

Upper medium temper‐

ature value that is map‐

ped to the upper nomi‐

nal range boundary se‐

lected by Current mode 

(9306). Applicable if 

Process value (9302) = 

3.

Max. medium 

temperature

[°C]

(7700)

-

Read / 

write

9376

Float / 4

Lower range 

value tempera‐

ture

Lower medium temper‐

ature value that is map‐

ped to the lower nomi‐

nal range boundary se‐

lected by Current mode 

(9306). Applicable if 

Process value (9302) = 

3.

Min. medium 

temperature

[°C]

(7700)

-

Read / 

write

9378

Float / 4

Upper range 

value standard 

volume flow

Upper standard volume 

flow value that is map‐

ped to the upper nomi‐

nal range boundary se‐

lected by Current mode 

(9306). Applicable if 

Process value (9302) = 

27.

0.4 % • max. 

standard vol‐

ume flow

[Sm

3

/h]

(7964)

-

Read / 

write

9380

Float / 4

Lower range 

value standard 

volume flow

Lower standard volume 

flow value that is map‐

ped to the lower nomi‐

nal range boundary se‐

lected by Current mode 

(9306). Applicable if 

Process value (9302) = 

27.

0.0

[Sm

3

/h]

(7964)

-

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

110

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments