manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 106 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 106

Channel 3 analog input settings

Table 4-41

Channel 3 analog input settings   

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

10522

Unsigned / 2

Current mode

Mode of current output. 0

● 0: 4-20 mA (3.5) 

3.8-20.5 (22.6) 
NAMUR

● 1: 4-20 mA (3.75) 

4.0-20.8 (22.6) US

● 2: 4-20 mA (2.0) 

4.0-20.5 (22.0)

● 3: 4-20 mA (2.0) 

4.0-24.0 (25.0)

● 4: 0-20 mA (0.0) 

0.0-20.5 (22.0)

● 5: 0-20 mA (0.0) 

0.0-24.0 (25.0)

Read / 

write

10531

Float / 4

Upper range 

value tempera‐

ture

Upper medium temper‐

ature value that is map‐

ped to the upper nomi‐

nal range boundary se‐

lected by Current mode 

(10522). Applicable if 

Process value (10523) 

= 1.

Max. medium 

temperature

[°C]

(7700)

-

Read / 

write

10533

Float / 4

Lower range 

value tempera‐

ture

Lower medium temper‐

ature value that is map‐

ped to the lower nomi‐

nal range boundary se‐

lected by Current mode 

(10522). Applicable if 

Process value (10523) 

= 1.

Min. medium 

temperature

[°C]

(7700)

-

Read / 

write

10537

Float / 4

Upper range 

value density

Upper process density 

value that is mapped to 

the upper nominal 

range boundary selec‐

ted by Current mode 

(10522). Applicable if 

Process value (10523) 

= 2.

1600.0

[kg/m3]

(7600)

-

Read / 

write

10539

Float / 4

Lower range 

value density

Lower process density 

value that is mapped to 

the lower nominal 

range boundary selec‐

ted by Current mode 

(10522). Applicable if 

Process value (10523) 

= 2.

600.0 
[kg/m3]
(7600)

-

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

106

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments