manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 79 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 79

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8527

Float / 4

Volume lower 

warning limit

Falling below this limit 

causes a warning when 

volume flow is selected 

as input.

Min. floating 

point value

[m

3

]

(8521)

 

Read / 

write

8529

Float / 4

Volume lower 

alarm limit

Falling below this limit 

causes an alarm when 

volume flow is selected 

as input.

Min. floating 

point value

[m

3

]

(8521)

 

Read / 

write

8531

Float / 4

Volume alarm 

hysteresis

Hysteresis that affects 

the alarm and warning 

limits when volume 

flow is selected as in‐

put.

0.0

[m

3

]

(8521)

-

Read / 

write

8506

Float / 4

Mass upper 

alarm limit

Exceeding this limit 

causes an alarm when 

mass flow is selected 

as input.

Max. floating 

point value

[kg]

(8520)

 

Read / 

write

8508

Float / 4

Mass upper 

warning limit

Exceeding this limit 

causes a warning when 

mass flow is selected 

as input.

Max. floating 

point value

[kg]

(8520)

 

Read / 

write

8510

Float / 4

Mass lower 

warning limit

Falling below this limit 

causes a warning when 

mass flow is selected 

as input.

Min. floating 

point value

[kg]

(8520)

 

Read / 

write

8512

Float / 4

Mass lower 

alarm limit

Falling below this limit 

causes an alarm when 

mass flow is selected 

as input.

Min. floating 

point value

[kg]

(8520)

 

Read / 

write

8514

Float / 4

Mass alarm hys‐

teresis

Hysteresis that affects 

the alarm and warning 

limits when mass flow 

is selected as input.

0.0

[kg]

(8520)

-

Read / 

write

8533

Float / 4

Standard vol‐

ume upper 

alarm limit

Exceeding this limit 

causes an alarm when 

volume flow is selected 

as input.

Max. floating 

point value

[Sl]

(8522)

 

Read / 

write

8535

Float / 4

Standard vol‐

ume upper 

warning limit

Exceeding this limit 

causes a warning when 

volume flow is selected 

as input.

Max. floating 

point value

[Sl]

(8522)

 

Read / 

write

8537

Float / 4

Standard vol‐

ume lower 

warning limit

Falling below this limit 

causes a warning when 

volume flow is selected 

as input.

Min. floating 

point value

[Sl]

(8522)

 

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

79

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments