manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 53 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 53

Modbus 

register

Data type / 

Size in bytes

Parameter

Description Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8993

Unsigned / 2

Volume units 

CH2

Units for 

volume 

quantities 

related to 

CH2 if in 

pulse 

mode.

41

● 40: US gallons
● 41: l (liters)
● 42: i.gal (Imperial gallons)
● 43: m³ (cubic meters)
● 46: BBL42 (1 barrel = 42 US 

gallons)

● 110: bush (bushels)
● 111: yd³ (cubic yards)
● 112: ft³ (cubic feet)
● 113: in³ (cubic inches)
● 124: BBL31.5 (1 barrel = 31.5 US 

gallons)

● 170: BBL31 (1 barrel = 31 US 

gallons)

● 236: hl (hectoliters)
● 253: custom units (see Custom 

volume units string (8452) / factor 
(8450))

Read / 

write

8992

Usigned / 2

Mass units CH2 Units for 

mass quan‐

tities rela‐

ted to CH2 

if in pulse 

mode.

61

● 60: g (grams)
● 61: kg (kilograms)
● 62: t (1 t = 1000 kg)
● 63: lb (pounds)
● 64: STon (1 STon = 2000 lb)
● 65: T (1 T = 2240 lb)
● 125: oz (ounces)
● 253: custom units (see Custom 

mass units string (8476) / factor 
(8474))

Read / 

write

8994

Unsigned / 2

Standard vol‐

ume units CH2

Units for 

standard 

volume 

quantities 

related to 

CH2.

171

● 166: Nm³ (normal cubic meters)
● 167: Nl (normal liters)
● 168: Sft³ (standard cubic feet)
● 171: Sl (standard liters)
● 172: Sm³ (standard cubic meters)

Read / 

write

9276

Unsigned / 2

Pulse width 

units CH3

Units of 

pulse dura‐

tion of 

CHh3 in 

pulse 

mode.

51

● 51: s (seconds)

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

53

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments