manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 111 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 111

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

10212

Float / 4

Upper range 

value current

Upper current value 

that is mapped to the 

upper nominal range 

boundary selected by 

Current mode (9306). 

Applicable if Process 

value (9302) = 25 or 26.

20.0

[mA]

-

Read / 

write

10214

Float / 4

Lower range 

value current

Lower current value 

that is mapped to the 

lower nominal range 

boundary selected by 

Current mode (9306). 

Applicable if Process 

value (9302) = 25 or 26.

4.0

[mA]

-

Read / 

write

9307

Float / 4

Damping value

Time constant of damp‐

ing filter for current out‐

put signal.

0.0

[s]

0.0 - 100.0

Read / 

write

9592

Unsigned / 2

Filter-safe acti‐

vation condition

Fail-safe activation con‐

dition.

1

● 0: Bad status of 

selected process 
value

● 1: Active 

Maintenance alarm 
or Failure (NAMUR)

Read / 

write

9481

Unsigned / 2

Fail-safe min. 

time

Minimum time the out‐

put stays in fail-safe be‐

havior.

0

[s]

0 - 100

Read / 

write

9314

Unsigned / 2

Fail-safe behav‐

ior

Current output reaction 

in case of a fault.

0

● 0: Lower fault current
● 1: Upper fault current
● 2: Last valid value
● 3: Disabled
● 4: Custom value

Read / 

write

9315

Float / 4

Fail-safe value

Output value in case of 

a fault and when Fail-

safe behavior (9314) is 

configured to 4.

0.0

[mA]

0.0 - 25.0

Read / 

write

7160

Float / 4

Forced value

Forced value when 

forcing is active.

4.0

[mA]

3.5 - 25.0

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

111

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments