Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 107

Page: 107 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

10524

Unsigned / 2

Fail-safe behav‐

ior

Reaction in case of a

fault at the current in‐

put.

● 0: Last valid value
● 1: Custom value

Read /

write

10535

Float / 4

Fail-safe tem‐

perature value

Input value in case of a

fault and when Fail-

safe behavior (10524)

configured to 1. Appli‐

cable if Process value

(10523) = 1.

Min. medium

temperature

[°C]

(7700)

Read /

write

10541

Float / 4

Fail-safe value

density

Input value in case of a

fault and when Fail-

safe behavior (10524)

configured to 1. Appli‐

cable if Process value

(10523) = 2.

600.0

[kg/m

]

(7600)

Read /

write

10520

Float / 4

Trimmed input

value

Provides the measured

current value.

Read

only

10508

Float / 4

Offset adjust‐

ment

Command to trim the

lower range value of

the analog input.
Provide a loop current

of 4.0 mA, read out the

value of Trimmed input

value and write the val‐

ue to this register.

Write on‐

10510

Float / 4

Gain adjustment Command to trim the

upper range value of

the loop current.
Simulate a loop current

of 20.0 mA, measure

the current with an am‐

pere meter and write

the measured value to

this register.

Write on‐

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

107

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 107 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: