manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 133 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 133

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

8081

Unsigned / 2

Trend log time 

window

Scaling of the time axis. 

Effective when Trend 

scale mode (8080) is 

set to 1.

1

● 0: 1 min
● 1: 5 min
● 2: 15 min
● 3: 30 min
● 4: 1 h
● 5: 2 h
● 6: 3 h

Read / 

write

8082

Float / 4

Trend scale low‐

er limit

Scaling of the y-axis. 

Lower limit. Effective 

when Trend scale 

mode (8080) is set to 1.

0.0

-

Read / 

write

8084

Float / 4

Trend scale up‐

per limit

Scaling of the y-axis. 

Upper limit. Effective 

when Trend scale 

mode (8080) is set to 1.

0.0

-

Read / 

write

4.10.5.11

Selectable values dependent on the view type

Selectable values dependent on the view type

Table 4-57

Selectable values dependent on the view type   

Selected view type

Setting options

Single value, Three values, 1 value 

and bar graph, 1 value and graph

● 0: Mass flow
● 1: Volume flow
● 2: Density
● 3: Medium temperature
● 4: Standard volume Flow
● 5: Fraction Flow Media A 
● 6: Fraction Flow Media B
● 7: Fraction Flow Media A in Percent
● 8: Fraction Flow Media B in Percent 
● 9: Reference density
● 11: Totalizer 1
● 12: Totalizer 2
● 13: Totalizer 3

Totalizer

● 11: Totalizer 1
● 12: Totalizer 2
● 13: Totalizer 3

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

133

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments