manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 95 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 95

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

9178

Float / 4

Upper range 

value standard 

volume flow

Upper standard volume 

flow value that is map‐

ped to the upper nomi‐

nal range boundary se‐

lected by Current mode 

(9106). Applicable if 

Process value (9102) = 

27.

0.4 % • max. 

standard vol‐

ume flow

[Sm

3

/s]

(7964)

-

Read / 

write

9180

Float / 4

Lower range 

value standard 

volume flow

Lower standard volume 

flow value that is map‐

ped to the lower nomi‐

nal range boundary se‐

lected by Current mode 

(9106). Applicable if 

Process value (9102) = 

27.

0.0

[Sm

3

/s]

(7964)

-

Read / 

write

10112

Float / 4

Upper range 

value current

Upper current value 

that is mapped to the 

upper nominal range 

boundary selected by 

Current mode (9106). 

Applicable if Process 

value (9102) = 25 or 26.

20.0

[mA]

-

Read / 

write

10114

Float / 4

Lower range 

value current

Lower current value 

that is mapped to the 

lower nominal range 

boundary selected by 

Current mode (9106). 

Applicable if Process 

value (9102) = 25 or 26.

4.0

[mA]

-

Read / 

write

9107

Float / 4

Damping value

Time constant of damp‐

ing filter for current out‐

put signal.

0.0

[s]

0.0 - 100.0

Read / 

write

9591

Unsigned / 2

Filter-safe acti‐

vation condition

Fail-safe activation con‐

dition.

1

● 0: Bad status of 

selected process 
value

● 1: Active 

Maintenance alarm 
or Failure (NAMUR)

Read / 

write

9281

Unsigned / 2

Fail-safe min. 

time

Minimum time the out‐

put stays in fail-safe be‐

havior.

0

[s]

0 - 100

Read / 

write

9114

Unsigned / 2

Fail-safe behav‐

ior

Current output reaction 

in case of a fault.

0

● 0: Lower fault current
● 1: Upper fault current
● 2: Last valid value
● 3: Disabled
● 4: Custom value

Read / 

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

95

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments