manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 169 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 169

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

9403

Unsigned / 2

Error status

Error status if config‐

ured to frequency out‐

put.

-

● Bit 0: Overflow
● Bit 1: Underflow
● Bit 2: Fail mode 

activated

Read 

only

10603

Float / 4

Current input 

value

Input current value if 

configured to current in‐

put.

-

-

Read 

only

10658

Unsigned / 2

Error status

Error status if config‐

ured to current input.

-

● Bit 0: Overflow (> 25 

mA)

● Bit 1: Underflow (< 0 

mA)

● Bit 2: Measured 

current out of 
measuring range

Read 

only

9329

Unsigned / 2

Digital input val‐

ue

Input value if config‐

ured to digital input.

-

-

Read 

only

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

169

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments