Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 58

Page: 58 / 198

4.10.5

Setup

4.10.5.1

Sensor settings

Table 4-12

General sensor settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

2100

Unsigned / 2

Flow direction

Define positive and

negative flow direction.

Default positive flow di‐

rection is indicated by

an arrow on the sensor.

● 0: Negative: The flow

is measured '+' in
default negative
direction and '-' in
default positive
direction.

● 1: Positive: The flow

is measured '+' in
default positive
direction and '-' in
default negative
direction.

Read /

write

2130

Unsigned / 2

Process Noise
Damping

Select process noise

dampinglevel:0: 55 ms

filtering (Centrifugal‐

Pump)1: 110 ms filter‐

ing (TriplexPump)2:

220 ms filtering (Du‐

plexPump)3: 400 ms fil‐

tering (Simplex‐

Pump)4: 800 ms filter‐

ing (CamPump)

0 Low to 4 High

Read /

write

2125

Float / 4

Low Massflow

Cut-Off

Set massflow limit for

lowflow cut-off.Below

this limit massflowout‐

put is forced to zero.If

Low Flow Cut-Off is set

to0, the cut-off function‐

ality isdisabled.No‐

tice:It is recommended

to set alower value for

gas applications.

Sensor size

specific

[kg/s]

0 to 1023

Read /

write

2426

Float / 4

Massflow Cor‐

rectionFactor

Specify correction fac‐

tor foruse in the mass‐

flow calculation

-1.999 to +1.999

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 58 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: