manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 116 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 116

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

9463

Float / 4

Amount of mass Amount value to gener‐

ate an output pulse. Ap‐

plicable if process val‐

ue (9460) is set to 0.

1.0

[kg]

(8992)

-

Read / 

write

9467

Float / 4

Amount of 

standard vol‐

ume

Amount value to gener‐

ate an output pulse. Ap‐

plicable if process val‐

ue (9460) is set to 27.

1.0

[Sl]

(8994)

-

Read / 

write

10255

Unsigned / 2

Pulses per 

amount

Number of pulses 

which will be output 

when configured 

amount is reached.

1

-

Read / 

write

9474

Float / 4

Pulse width

Pulse duration.

0.1

[s]

0.00004 - 4.0

Read / 

write

9477

Unsigned / 2

Polarity

Logical polarity of pulse 

output.

0

● 0: Active high level
● 1: Active low level

Read / 

write

9592

Unsigned / 2

Fail-safe activa‐

tion condition

Fail safe activation con‐

dition.

1

● 0: Bad status of 

selected process 
value

● 1: Active 

Maintenance alarm 
or Failure (NAMUR)

Read / 

write

9481

Unsigned / 2

Fail-safe min. 

time

Minimum time the out‐

put stays in Fail-safe 

behavior.

0

[s]

0 - 100

Read / 

write

9461

Unsigned / 2

Fail-safe behav‐

ior

Pulse output reaction in 

case of a fault.

0

● 0: Last valid value
● 1: Hold. Value 0.0 

substitutes the actual 
input value

● 2: Disabled
● 3: Custom value

Read / 

write

7441

Float / 4

Fail-safe value

Output value in case of 

a fault and when Fail-

safe behavior (9461) is 

configured to 4.

0.0

[pulses/s]

0.0 - 12500.0

Read / 

write

7165

Float / 4

Forced value

Forced value when 

forcing is active.

1.0

[pulses/s]

0.0 - 12500.0

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

116

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments