Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 160

Page: 160 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

9617

Float / 4

Recipe 3 fixed

compensation
Volume flow

Fixed compensation

volume flow value that

is used to close the

valve(s) before the

measured amount val‐

ue has reached the tar‐

get amount

Read /

write

9619

Float / 4

Recipe 3 fixed

compensation
Corrected vol‐

ume flow

Fixed compensation

corrected volume flow

value that is used to

close the valve(s) be‐

fore the measured

amount value has

reached the target

amount

Read /

write

9691

Unsigned / 2

Recipe 3 com‐

pensation mode

Compensation algo‐

rithm, fixed or adaptive

compensation

0: fixed compensation

value is taken
1: On Target
2: Target plus
3: Target minus

Read /

write

9625

Float / 4

Recipe 3 over‐

run mass flow

value

When the amount

mass flow has reached

this value a dosing

overrun fault is raised.

Read /

write

9627

Float / 4

Recipe 3 over‐

run volume flow

value

When the amount vol‐

ume flow has reached

this value a dosing

overrun fault is raised.

Read /

write

9629

Float / 4

Recipe 3 over‐

run corrected

volume flow val‐

When the amount cor‐

rected volume flow has

reached this value a

dosing overrun fault is

raised.

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

160

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 160 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: