Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 115

Page: 115 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9592

Unsigned / 2

Fail-safe activa‐

tion condition

Fail-safe activation con‐

dition.

● 0: Bad status of

selected process
value

● 1: Active

Maintenance alarm
or Failure (NAMUR)

Read /

write

9481

Unsigned / 2

Fail-safe min.

time

Minimum time the out‐

put stays in fail-safe be‐

havior.

[s]

0 - 100

Read /

write

9439

Unsigned / 2 Fail-safe behav‐

ior

Frequency output reac‐

tion in case of a fault.

● 0: Frequency value

low

● 1: Frequency value

high

● 2: Last valid value
● 3: Disabled
● 4: Custom value

Read /

write

9440

Float / 4

Fail-safe value

Output value in case of

a fault and when Fail-

safe behavior (9439) is

configured to 4.

0.0

[Hz]

0.0 - 12500.0

Read /

write

7163

Float / 4

Forced value

Forced value when

forcing is active.

1.0

[Hz]

0.0 - 12500.0

Read /

write

Channel 4 pulse output settings

Table 4-45

Channel 4 pulse output settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

9460

Unsigned / 2

Process value

Select process value

for the pulse output.

● 0: Mass flow
● 1: Volume flow
● 27: Standard volume

flow rate (only
hydrocarbon and gas
applications)

Read /

write

9462

Unsigned / 2

Flow direction

Flow direction filter.

● 0: Positive direction
● 1: negative direction
● 2: Positive and

negative directions

Read /

write

9465

Float / 4

Amount of vol‐

ume

Amount value to gener‐

ate an output pulse. Ap‐

plicable if process val‐

ue (9460) is set to 1.

0.001

]

(8993)

Read /

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

115

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 115 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: