Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 176

Page: 176 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

6182

Unsigned / 2

Backup

Command to overwrite

the existing backup da‐

ta sets.

This ensures that the

current sensor serial

number and transmitter

serial numbers are up‐

dated in the backup da‐

taset. This enables the

automatic backup.

● 1: Overwrite existing

backup files

Write on‐

6099

Unsigned / 2

Restore

Command to restore

backup data. Coding is

bitwise.

● Bit 0: Restore sensor

setup parameters

● Bit 1: Restore sensor

application setup
parameters

● Bit 2: Restore

transmitter
application setup
parameters

● Bit 3: Restore

customer transmitter
configuration setup
parameters

● Bit 4: Restore

totalizers

● Bit 5: Restore system

setup

● Bit 6: Restore

customer sensor
configuration setup
parameters

Write on‐

4.10.10.2

Data logging

Table 4-93

Data logging

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

11400

Unsigned / 2

Enable / disable Controls data logging.

● 0: Disabled
● 1: Enabled

Read /

write

11401

Unsigned / 2

Data logging

mode

Controls data logging

mode.

● 0: Log instantaneous
● 1: Log average value

Read /

write

11402

Unsigned / 4

Logging interval Defines interval for log‐

ging. Granularity is 10

ms.

500

[x 10 ms]

1 - 8640000

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

176

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews:

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 176 / 198

Search results

Summary of Contents for SITRANS F Coriolis FCT030

Reviews: