manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Function Manual, Page: 90 / 198

Share
Download
Siemens SITRANS F Coriolis FCT030 Function Manual Download Page 90

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

7421

Float / 4

Fail-safe value

Output value in case of 

a fault and when Fail-

safe behavior (8939) is 

configured to 4.

0.0

[pulses/s]

0.0 - 12500.0

Read / 

write

7151

Float / 4

Forced value

Forced value when 

forcing is active.

1.0

[pulses/s]

0.0 - 12500.0

Read / 

write

Channel 2 status output settings

Table 4-34

Channel 2 status output settings   

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[units]

(units register)

Value range / 

Setting options

Access 

level

8841

Unsigned / 2

Status mode

Select the functionality 

for the status output.

0

● 0: Alarm class
● 1: Alarm item

Read / 

write

8858

Unsigned / 2

Alarm class

Bit encoded selection 

of alarm classes which 

impact the status out‐

put. Each diagnostic 

event is allocated to an 

alarm class. See Alarm 

items (Page 145).
Applicable if Status 

mode = 0.

0

● Bit 0: Process value 

alarm (PA)

● Bit 1: Process value 

warning (PW)

● Bit 2: Maintenance 

alarm (MA)

● Bit 3: Maintenance 

warning (MW)

● Bit 4: Maintenance 

required (MR)

● Bit 5: Function check 

(FC)

Read / 

write

8899

Unsigned / 2

NAMUR status 

signals

Bit encoded selection 

of NAMUR status sig‐

nals which impacts the 

status output.
Applicable if Status 

mode = 0. NAMUR sta‐

tus is derived from 

Alarm class (8858).
 

0

● Bit 0: Out of 

specification (PA, 
PW)

● Bit 1: Failure (MA)
● Bit 2: Maintenance 

required (MR, MD)

● Bit 3: Function check 

(FC)

Read / 

write

8842

Unsigned / 4

Alarm items 1

Bit encoded selection 

of alarm items that im‐

pact the output. Mainly 

sensor alarms. See 

Alarm items 

(Page 145). Applicable 

if Status mode = 1.

0

 

Read / 

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

90

Function Manual, 06/2018, A5E39931813-AB

Summary of Contents for SITRANS F Coriolis FCT030







































































































































































































Reviews:

No comments