ROBBE-Futaba FX-32 Instruction Manual Download Page 12

Page: 12 / 180

<Before Use>

• 7,4V 3,400mAh transmitter battery pack - the transmitter LiPo battery pack may be easily exchanged with

a fresh one to provide enough capacity for extended flying sessions.

• Trainer cord - the optional training cord may be used to help a beginning pilot learn to fly easily by

placing the instructor on a separate transmitter. Note that the FX-32 transmitter may be connected to

another FX-32 system, as well as to any other models of Futaba transmitters. The FX-32 transmitter uses

one of the three cord plug types according to the transmitter connected. (Refer to the description at the

TRAINER function instructions). The part number of this cord is: FUTM4405.

• Servos - there are various kinds of servos. Please choose from the servos of Futaba what suited the model

and the purpose of using you. If you utilize a S.BUS system, you should choose a S.BUS servo. An

analog servo cannot be used if "FASSTest12CH mode" is used.

• Telemetry sensor - please purchase an optional sensor, in order to utilize bidirectional communication

system and to acquire the information from a model high up in the sky.

[

Temperature sensor : SBS-01T] [Altitude sensor : SBS-01A] [RPM sensor

magnet type : SBS-01RM]

[RPM sensor

optical type : SBS-01RO] [GPS sensor : SBS-01G] [Voltage sensor : SBS-01V]

• Neckstrap - a neckstrap may be connected to your FX-32 system to make it easier to handle and improve

your flying precision since your hands won’t need to support the transmitter’s weight.

• Y-harnesses, servo extensions, hub,etc - Genuine Futaba extensions and Y-harnesses, including a heavy-

duty version with heavier wire, are available to aid in your larger model and other installations.

• Gyros - a variety of genuine Futaba gyros is available for your aircraft or helicopter needs.

• Governor - for helicopter use. Automatically adjusts throttle servo position to maintain a constant head

speed regardless of blade pitch, load, weather, etc.

• Receivers - various models of Futaba receivers may be purchased for use in other models. (Receivers for

FASSTest and FASST,S-FHSS types are available.)

The following additional accessories are available from your dealer. Refer to a Futaba catalog for

more information:

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands