ROBBE-Futaba FX-32 Instruction Manual Download Page 149

Page: 149 / 180

149

<Model Menu (Airplane/Glider Functions)>

● S e l e c t t h e f u n c t i o n

name and return to the

preceding screen by

touching the

RTN

button

or pushing the

Home/Exit

button.

<SensorTouch™>

SNAP ROLL

[Corresponding model type]: Airplane, general

This function selects the switch and rate

adjustment of each rudder, (ailerons, elevators, or

flaps) when a snap roll is performed.

● Four snap roll directions can be set. (Right/up,

right/down, left/up, left/down)

● Operation mode: When [Master] mode is selected,

the Snap Roll function is turned ON/OFF by master

switch in the state in which the direction switch

was switched to the direction in which you want

to snap roll. When [Single] mode is selected, snap

roll in each direction can be executed by means

of independent switches.

● A safety switch can be set. As a safety measure,

the switch can be set so that snap roll is not

executed when, for instance, the landing

gear is lowered, even if the switch is turned on

accidentally. The snap roll switch is activated only

when the safety switch is ON.

● The operation speed of the aileron, elevator, and

flap servos can be adjusted for each snap roll

direction. (In side/out side)

(Example) Setting example for F3A

● Mode: [Master]
● Safety SW: [SW-G] (Safety measure)
● Master SW: [SW-H] (Main switch for

executing snap roll)

● Direction switches:

*The snap roll up side left and right and down side left and right

direction switches are selected here.

Right/Up: OFF [SW-D]

Right/Down: OFF [SW-D]

Left/Up: OFF [SW-A]

Left/Down: OFF [SW-A]

● Speed adjustment

The operation speed of each control

surface when the snap switch is ON can

be changed and snap roll executed by

stick while there is switch operation can be

performed.

● Rate adjustment
1. Move the cursor to the item you want to

adjust and touch the RTN button to switch to

the data input mode.

2. Adjust rate by scrolling the touch sensor.
3. Touch the RTN button to end adjustment and

return to the cursol move mode.

● Group/single mode switching

(For more information, see the description at the back of this

manual.)

● Direction switches

● Adjustment of the servo speed of each

rudder

(For a description of the setting method, see the description at

the back of this manual.)

(Currently selected condition name)

● Select [SNAP ROLL] at the model menu

and call the setup screen shown

below by touching the RTN button.

Scrolling

● Moving cursor

● Selecting mode

● Adjusting value

● To next page

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands