manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 161

161

<Functions of Model Menu (Helicopter Functions)>

● S e l e c t   t h e   f u n c t i o n 

name and return to the 

p r e c e d i n g   s c r e e n b y 

touching the

 RTN

 button 

or pushing the 

Home/Exit 

button.

<SensorTouch™>

PIT to NEEDLE mixing

This mixing is used when the engine is equipped 

with needle control or other fuel-air mixture 

adjustment. A needle curve can be set.

An acceleration function which temporarily 

increases needle operation at throttle stick 

Setting method

● When using this function, move the cursor 

to the [ACT] item and touch the RTN button 

to switch to the data input mode. Turn the 

touch sensor to the left and touch the RTN 

button. (ON  is displayed.)

● When you want to set the same contents at 

other conditions, select the group mode. 

  When you want to set the selected condition 

only, select the single mode (initial setting).

●  A needle curve can be set.
●  A switch can be set.
  When  [  [--]]  is  set,  the  mixing  function  is 

operated by merely selecting the condition.

  When setting an [ON]/[OFF] switch, move 

the cursor to the [--] item and touch the RTN 

button to switch to the data input mode. 

Touch the RTN button to call the selection 

screen and set the switch and its ON position.

< Acceleration function setting>

●Acceleration  can  be  set  at  both  setting 

at  acceleration  (high)  and  setting  at 

deceleration (low).

●The acceleration rate (rate) and the return 

time after operation (dumping) can be set.

●An operation point (act pos) at acceleration 

and  deceleration  can  be  set.  When 

an  operation  point  was  exceeded, 

acceleration operation is performed.

● Normally, use [POINT] type.

● Select [PIT to NEEDLE] at the model menu and call 

the setup screen shown below by touching the 

RTN button.

(Currently selected condition name)

acceleration/deceleration operation can be set. 

The rise characteristic of the needle servo at 

acceleration and deceleration operation can be 

adjusted.

● Group/single mode switching

(For more information, refer to the 

description at the back of this manual.)

● Mixing curve setting

*For a description of the curve setting method, see 

the description at the back of this manual.

●Acceleration settings

Scrolling

● Moving cursor

● Selecting mode

● Adjusting value

● To next page

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands