manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 64

64

<Functions of Linkage Menu>

● Select the function name 

and return to the Linkage 

menu  by  touching  the

 

RTN

 button or pushing the 

Home/Exit 

button.

<SensorTouch™>

WARNING

  Don't set a servo test mode when the drive 

motor is connected and the engine was started.

■

Inadvertent rotation of the motor or acceleration of the 

engine is extremely dangerous.

SERVO MONITOR

Servo Test & Graph Display / Displays servo positions.

This is used for testing servo movement.  

“Moving Test” (repetition mode) and “Neutral 

Test” (fixed position mode) are available. 

 The “Neutral Test” is good for finding the 

neutral position of a servo horn.

In order to prevent any potential difficulties, 

the servo test function will be inoperable, or 

inaccessible, under certain conditions.  Specifically, 

the Servo Test function is not operational if the 

Throttle Cut is ON in either airplane or helicopter 

modes; or if the Throttle Hold is ON in Helicopter 

mode.

● Select [SERVO MONITOR] at the linkage menu and 

call the setup screen shown below by touching 

the RTN button.

Servo test operation

1. Use the touch sensor to move the cursor to 

the [TEST] item and touch the RTN button to 

switch to the data input mode. 

  Select the test mode by turning the touch 

sensor to the left or right and touch the RTN 

button.

  [MOVING]: Mode which repeats operation of 

each servo

  [NEUTRAL]: Mode which locks each servo in 

the neutral position

2. Use the touch sensor to move the cursor to 

the [TEST] item and touch the RTN button to 

switch to the data input mode.

  Select the [OFF] by turning the touch sensor 

and touch the RTN button. Testing is stopped.

*The display screen is an example. The screen 

depends on the model type.

Scrolling

● Moving cursor

● Selecting mode

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands