manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 89

89

<Functions of Linkage Menu>

● Select the function name 

and return to the Linkage 

menu  by  touching  the

 

RTN

 button or pushing the 

Home/Exit 

button.

<SensorTouch™>

TELEMETRY

Displaying data from the receiver 

This screen displays your choice of data from the 

receiver.

Also warnings can be activated regarding 

other data from your aircraft.  For example, if the 

receiver voltage drops, the user can be warned by 

an alarm (and vibration).

*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in 

FASSTest12CH mode.

*The FASSTest18CH mode can use all the telemetry functions. 

●  Select  [TELEMETRY]  in  the  Linkage  menu  and 

access the setup screen shown below by touching 

the RTN button.

● Push 

S1

 button to advance to next page.

Scrolling

● Moving cursor

● To next page

● Receiver

→

 Transmitter. The 

reception strength is shown.

How to see telemetry date

1. Telemetry  screen  can  be  called  select 

[TELEMETRY] in the Linkage menu and access 

the setup screen by touching the RTN button. 

2. If each item is chosen and the RTN button is 

pushed, an alarm setup can be performed 

w i t h   t h e   m i n i m u m / m a x i m u m   a f t e r   a 

transmitter is turned on. 

*Receiver voltage can be checked immediately. An optional 

sensor will need to be attached to S.BUS2 of a receiver if 

you would like to see other information. 

 

*No special setup is necessary if each sensor displayed 

is left as in the default setup. Separate sensor ID 

is also unnecessary. However, if two or more of 

one kind of sensor is used, setup is required in the 

"SENSOR" menu.

WARNING

 Do not watch the transmitter screen during 

flight.

*You may loose sight of the aircraft during flight and this is 

extremely dangerous. Have an assistant on hand to check 

the screen for you.  A pilot should NEVER take his eyes off 

his aircraft.

Note:
Any change in the selected language only alters 
the language used in the on-screen menus, i.e. 
not the language used for speech output. To 
change the speech output language an update 
must be installed containing the corresponding 
speech software. This software can be found in 
the Registration area of the robbe website: www.
robbe.com

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands