ROBBE-Futaba FX-32 Instruction Manual Download Page 21

Page: 21 / 180

<Before Use>

Installation and removal of the HT6F1800B

transmitter battery
Attachment of the battery

1. Open the rear case.

2. A battery is fixed using two bands.
3. Connect the battery connector.

4. Close the rear case completely.

Battery removal
Note: If you remove the battery while the

power is on, the data you have set will not

be saved.

1. Open the rear case.

2. Disconnect the battery connector.
3. Two bands are removed and the remove the

battery.

4. Close the rear case completely.

WARNING

Be careful not to drop the battery.

Never disconnect the battery connector

from the FX-32 transmitter after turning

off the power until the screen is completely

blank and the transmitter has shut down

completely.

* Internal devices such as memories may be damaged.
* If there is any problem, the message "Backup Error" will

be shown the next time when you turn on the power of the

transmitter. Do not use the transmitter as it is. Send it to the

Futaba service center.

HT6F1800B

Battery

Band

Connector

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands