ROBBE-Futaba FX-32 Instruction Manual Download Page 65

Page: 65 / 180

<Functions of Linkage Menu>

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

<SensorTouch™>

MODEL SELECT

The Model Selection function performs model addition, call,

deletion, copy, and model name setting.

This function is used to load the settings of the

desired model into the FX-32’s memory.

The settings may be selected from either the

transmitter’s built-in memory or a SD card (32MB-

2GB). Remember that up to 30 model memories are

available in the transmitter.

The name of the model stored in the transmitter and

the SD card may be changed. This can be very useful

to tell different models settings apart. Each model name

can be as long as 15 characters, and the model name

always appears in the display screen.

The Copy function is used to copy one set of model

data into a second memory within the transmitter and

the SD card. It may be used for getting a head-start on

setting up models with almost the same settings (only

differences need to be modified, instead of entering the

complete model from scratch). Also, this function may

be used to make a backup copy of a model setup before

any changes are made.

Model call

*Model data saved at models other than the model currently

used or saved on a SD card can be called.

1. Use the touch sensor to move to the save

destination ("INTERNAL" or "MEM.CARD") and

touch the RTN button to switch to the data

input mode.

Select the location which is to save the

desired model by turning the touch sensor to

the left or right. Touch the RTN button.

[INTERNAL]: Transmitter memory
[MEM. CARD]: SD card
2. After using the touch sensor to move the

cursor to the desired model in the model list,

touch the RTN button.

3. Use the touch sensor to move to [SELECT].
4. Touch the RTN button. When a confirmation

message is displayed and the RTN button is

touched again, calling is complete.

*Transmission stops and a send with new model confirmation

message ("TRANSMIT?") appears.

5. To start transmission, use the touch sensor to

select [YES] and then touch the RTN button.

To not transmit, select [NO] and touch the

RTN button.

Model addition

*A new model can be added to the transmitter memory or SD

card.

1. Use the touch sensor to move the cursor to

the save destination ("INTERNAL" or "MEM.

CARD) and touch the RTN button to switch to

the data input mode.

Select the save destination by turning the

touch sensor to the left or right. Touch the

RTN button.

[INTERNAL]: Transmitter memory
[MEM. CARD]: SD card
2. Use the touch sensor to move to [NEW].
3. Press the RTN button. A confirmation message

appears. Press the RTN button again.

*The model type setup screen and frequency setup screen are

automatically displayed. Confirm or change the model type

and frequency.

*A starting transmission with new model confirmation

message ("TRANSMIT") appears.

4. To start transmission, use the touch sensor to

select [YES] and then touch the RTN button.

To not transmit, select [NO] and touch the

RTN button.

*The added model appears in the model list.

● Select [MODEL SELECT] at the linkage menu and

call the setup screen shown below by touching

the RTN button.

*The display screen is an example. The screen

depends on the model type.

(Model list)

●"Save to"
[INTERNAL]: transmitter memory
[MEM.CARD]: SD card

Scrolling

● Moving cursor

● Selecting mode

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands