ROBBE-Futaba FX-32 Instruction Manual Download Page 103

Page: 103 / 180

103

<Functions of Linkage Menu>

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

● Call page 3/3 by touching the S1 button 2 times

from the [SENSOR] menu.

● Call page 3/3 by touching the S1 button 2 times

from the [SENSOR] menu.

SENSOR : RELOAD

SENSOR : REGISTER

This page is set when using multiple telemetry sensors of the same type.

When using multiple sensors of the same type

the sensors must be registered in the transmitter.

Connect all the sensors to be used to the FX-32 as

shown in the figure at the right and register them by

the following procedure. The ID of each sensor is

registered in the transmitter.

This function registers an additional sensor.

Connect the sensor as shown in the figure at the

right and register it by the following procedure.

The sensor ID is registered in the transmitter.

All the sensors to be used are connected.

SENSOR

3-way hub

or Y-harnesses

FX-32

SENSOR

FX-32

SENSOR

Reading all the sensors to be used

1. Connect all the sensors to be used to the

FX-32 through a hub as shown in the figure

above.

2. Move the cursor to “RELORD” on page 3/3 of

the [SENSOR] screen.

3. Touch the RTN button.
All the sensors are registered and can be

used.

Additional sensor registration

1. Connect the sensor to be used to the FX-32

through a hub as shown in the figure at the

right.

2. Move the cursor to “REGISTER” on page 3/3

of the <Sensor> screen.

3. Touch the RTN button.
The sensor is registered and can be used.

When the number of slots needed in registration is

insufficient, an error is displayed and registration cannot be

performed. Disable unused slots or perform the following

relocate.

*It is not necessary to carry out

multiple connection of the

battery like a T18MZ/T14SG.

(It will damage, if it connects.)

*It is not necessary to carry out

multiple connection of the

battery like a T18MZ/T14SG.

(It will damage, if it connects.)

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands