ROBBE-Futaba FX-32 Instruction Manual Download Page 101

Page: 101 / 180

101

<Functions of Linkage Menu>

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

<SensorTouch™>

TELEMETRY : GPS [ALTITUDE, VARIOMETER, POSITION]

The altitude, variometer, position screen displays

and sets the data from an SBS-01G (GPS sensor)

sold separately.

*The GPS sensor is necessary, and is sold separately. Mount

and connect the sensor in accordance with the sensor

instruction manual.

*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH mode can use all the telemetry functions.

*A GPS sensor must be installed in the aircraft.

●This indicates the receiving accuracy

from a GPS Satellite. When three bars

are displayed, the GPS is ready for use.

● Select [GPS] in the TELEMETRY screen and

access the setup screen shown below by

touching the RTN button.

● Push

button to advance to next page.

● Refer to the former

page for a setup

about

ALTITUDE

and

VARIOMETER

● Push

button to advance to next page.

● The position of the present model is displayed.

Scrolling

● Moving cursor

● To next page

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands