ROBBE-Futaba FX-32 Instruction Manual Download Page 90

Page: 90 / 180

<Functions of Linkage Menu>

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

<SensorTouch™>

TELEMETRY : RECEIVER [BATTERY]

Displaying data from the receiver

battery voltage

In this screen, the battery voltage of a receiver is

displayed.

If it becomes higher or lower than the setting an

alarm and/or vibration will alert you.

*It cannot be used in FASST mode and S-FHSS mode.
*Only receiver voltage and EXT voltage can be used in

FASSTest12CH mode.

*The FASSTest18CH mode can use all the telemetry functions.

● Select [Rx-BATT.] in the TELEMETRY screen

and access the setup screen shown

below by touching the RTN button.

● Select [BATTERY] in the RECEIVER screen

and access the setup screen shown

below by touching the RTN button.

●A setup of the voltage on

which the alarm operates.

Scrolling

● Moving cursor

● Receiver battery voltage

● The maximum and the minimum

when powering ON are shown.

It will be preset, if a cursor is

moved to this place and the

RTN button is pushed for 1

second.

● ↓The "down" arrow will

indicate that an alarm

will sound when the

voltage drops to below

the setting.

● ALARM is chosen from

BUZZER, VOICE, and

INHIBIT.

● The ON/OFF switch of SPEECH is

chosen.

Alarm set

1. Move the cursor to the ↓ALARM item, and

it chooses from BUZZER, VOICE, INHIBIT, and

pushes RTN.

2. When not operating vibrator, it is

VIBRATOR"

to INHIBIT. TYPE1-3 will be chosen if it is made

to operate.

3. Move the cursor to the LIMIT [4.0V] item and

touch the RTN button to switch to the data

input mode.

4. Ajust the rate by scrolling the touch sensor.
Initial value: 4.0V
Adjustment range: 0.0V~100.0V

*When the RTN button is touched for one second, the rate is

reset to the initial value.

5. Touch the RTN button. (To terminate the input

and return to the original state, touch the

Home/Exit button.)

TYPE 1

TYPE 2

TYPE 3

"VIBRATOR" type

If the following types are selected, the transmitter

will vibrate during the warning.

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands