manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 56

56

<Model Basic Setting Procedure>

11. Swash Mix corrects aileron, elevator and 

pitch interaction

The swash mix function is used to correct the 

swash plate in the aileron (Left/Right Cyclic) 

and elevator (Forward/Aft Cyclic) direction 

corresponding to each operation of each condition.

12. Throttle mixing setting

*If throttle mixing is necessary for a compensation for 

slowing of engine speed caused by swash plate operation 

during aileron or elevator operation, please refer to the 

THROTTLE MIX function.

13. Other special mixings

●Pitch to Needle mixing

This mixing is used with engines with a construction 

which allows needle control during flight (fuel-air 

mixture adjustment). A needle curve can be set. 

The needle servo rise characteristics at throttle 

stick acceleration/deceleration operation can be 

adjusted. (Acceleration function)

●Governor mixing

This mixing is dedicated governor mixing when a 

governor is used. Up to 3 rates (speeds) can be 

switched for each condition.

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands