ROBBE-Futaba FX-32 Instruction Manual Download Page 77

Page: 77 / 180

<Functions of Linkage Menu>

● Select the function name

and return to the Linkage

menu by touching the

RTN

button or pushing the

Home/Exit

button.

<SensorTouch™>

(The display screen is an example. The screen

depends on the model type.)

● Select [FAIL SAFE] at the linkage menu and call the

setup screen shown below by touching the RTN

button.

FAIL SAFE

Sets the servos operating position when transmitter signals can no

longer be received or when the receiver battery voltage drops.

The Failsafe function may be used to set up

positions that the servos move to in the case of

radio interference.

You may set either of two positions for each

channel: Hold, where the servo maintains its last

commanded position, or Failsafe, where each

servo moves to a predetermined position. You may

choose either mode for each channel. (

FASST 7CH

mode: CH3 only

)

The FX-32 system also provides you with

an advanced battery monitoring function that

warns you when the receiver battery has only a

little power remaining. In this case, each servo is

moved to the defined failsafe position. (

FASST

7CH mode: CH3 only

) The battery failsafe may

be released by operating a predefined control on

the transmitter, do not continue to fly, land as

soon as possible. Remember, if the predefined

Fail safe setting procedure

1. Move the cursor to the "F/S" item of the

channel you want to set and touch the RTN

button to switch to the data input mode.

2. Select the F/S mode by scrolling the touch

sensor. A confirmation message appears.

*The display blinks.

3. Touch the RTN button. (Touch the S1 button

to stop setting.)

*The channel switches to the F/S mode.

4. Move the cursor to the "POS" item.
Hold the corresponding stick, knob, slider,

etc. in the position you want the servo

to move to when the fail safe function is

activated and touch the RTN button for one

second.

*The set position is displayed in percentage.

*If you want to return that channel to the hold mode, move

the cursor to the "F/S" item and touch the RTN button

to switch to the data input mode. Select the F/S mode by

scrolling the touch sensor. A confirmation message appears

and then change the mode by touching the RTN button.

control suddenly moves to a position you did not

command, land at once and check your receiver

battery.

Defines servo position when signals are lost and

when receiver battery voltage becomes low.

WARNING

For safety, always set the fail safe functions.

●Remember to set the throttle channel fail safe function so that

the servo moves to the maximum slow side for airplanes and
to the slow side from the hovering position for helicopters.
Crashing of the model at full high when normal radio waves
cannot be received due to interference, etc., is very dangerous.

●If the battery fail safe is reset by the throttle stick, it may

be mistaken for an engine malfunction and will be reset at

throttle slow and the model will continue to fly. If you have

any doubts, immediately land.

Battery fail safe setting procedure

Battery fail safe can be set for each channel

by the same method as the fail safe setting

procedure. Select and set the "B.F/S" item.

[ON]: Battery fail safe function ON
[OFF]: Battery fail safe function OFF

Battery fail safe release switch setting

This function temporarily releases the battery

fail safe function, so the fuselage can

recover after the battery fail safe function

was activated by a drop in the receiver

battery voltage. This setting selects the switch

which releases the battery fail safe function.

1. Move the cursor to the [RELEASE B.F/S] item in

the setup screen (last page).

2. Touch the RTN button.

*The switch selection screen is called.
*For a detailed description of the switch selection and ON/

OFF direction setting method, see [Switch Setting Method]

at the back of this manual.

Scrolling

● Moving cursor

● Selecting mode

● Push the

button to

call next page.

Summary of Contents for FX-32





















































































































































































Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands

ROBBE-Futaba FX-32, Instruction Manual

Search results

Summary of Contents for FX-32

Reviews:

Related manuals for FX-32

Brands by name

Popular brands