manualshive.com logo in svg

ROBBE-Futaba FX-32, Instruction Manual

Share
Download
ROBBE-Futaba FX-32 Instruction Manual Download Page 17

17

<Before Use>

Note:

*Scroll operation: Circle your finger on the outside edge of 

the RTN button.  The sensors may mis-read your touch as a 

reverse rotation if the circle is smaller, or performed on the 

inside edge of the RTN button. 

* The SensorTouch™ may not operate smoothly if your hand 

is touching the surrounding case parts.  As such, please 

make sure that the tip of your finger is actually operating the 

SensorTouch™. 

*If the SensorTouch™ does not register your input, please 

try again after lightly tapping your finger on the sensor once 

again.

* Do not operate the SensorTouch™ with gloves worn. The 

SensorTouch™ might not react.

CAUTION

The touch sensor might not operate by 

receiving the spark noise generated from 

the gasoline engine etc. In this case, please 

operate your transmitter from the noise 

source apart.

Stick Adjustment
Adjustment of the stick lever length

You can adjust the length of stick levers, as you 

like. It is recommended to adjust the length of the 

sticks in line with your hand size. 

1. Hold the lever head "B" and turn the lever head "A" 

counter-clockwise. The lock will be released.

2. Turn the lever-head "A" clockwise as you hold the 

lever-head "B" after placing it as you like.

Adjustment of stick lever tension

The tension of the self-return type stick lever can 

be adjusted.

1. First, Remove the battery cover on the bottom of 

the transmitter. Next, unplug the battery wire and 

remove the battery from the transmitter.

2. Next, using a screwdriver, remove the  five screws 

that hold the transmitter's rear case in position, 

and put them in a safe place. Gently ease off the 

transmitter's rear case.

  Now you'll see the view shown in the figure below.

3. Use  a  1.5mm  hexagonal  wrench  to  adjust  the 

spring strength as you prefer by turning the 

adjusting screw of the stick you want to adjust.

*Turning the screw clockwise increases the tension.

  CAUTION:  If  you  loosen  the  screw  too  much, 

the stick may not operate because it is caught 

internally.

4. At the end of adjustment, re-install the rear case.

•Stick Tension (J2)

(Mode 2)

•Stick Tension (J1)

(Mode 1/2)

•Stick Tension (J4)

(Mode 1/2)

•Stick Tension (J3)

(Mode 1)

A

Lever Head 

B

Lever Head 

Screw is clockwise.

1.5mm Hexagonal wrench is used

Stick tension maximum

Stick tension minimum 

Screw is counter-clockwise.

*Don't loosen a screw any more. 

A screw sticks out too far and it 

interferes in a case.

The interval of a spring 

hook is short.

The interval of a spring 

hook is short.

The interval of a spring 

hook is short.

The interval of a spring 

hook is long.

Summary of Contents for FX-32





















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands